Code
|
Message |
600
|
An operation is pending |
601
|
The port handle is invalid |
602
|
The port is already open |
603
|
Caller's buffer is too small |
604
|
Wrong information specified |
605
|
Cannot set port information |
606
|
The port is not connected |
607
|
The event is invalid |
608
|
The device does not exist |
609
|
The device type does not exist |
610
|
The buffer is invalid |
611
|
The route is not available |
612
|
The route is not allocated |
613
|
Invalid compression specified |
614
|
Out of buffers |
615
|
The port was not found |
616
|
An asynchronous request is pending |
617
|
The port or device is already disconnecting |
618
|
The port is not open |
619
|
The port is disconnected |
620
|
There are no endpoints |
621
|
Cannot open the phonebook file |
622
|
Cannot load the phonebook file |
623
|
Cannot find the phonebook entry |
624
|
Cannot write the phonebook file |
625
|
Invalid information found in the phonebook |
626
|
Cannot load a string |
627
|
Cannot find a key |
628
|
The port was disconnected |
629
|
The port was disconnected by the remote machine |
630
|
The port was disconnected due to hardware failure |
631
|
The port was disconnected by the user |
632
|
The structure size is incorrect |
633
|
The port is already in use or is not configured for DUN/RAS dial-out |
634
|
Cannot register your computer on the remote network |
635
|
Unknown error |
636
|
The wrong device is attached to the port |
637
|
The string could not be converted |
638
|
The request has timed out |
639
|
No asynchronous net available |
640
|
A NetBIOS error has occurred |
641
|
The server cannot allocate NetBIOS resources |
642
|
One of your NetBIOS names is already is already registered on the remote network |
643
|
A network adapter at the server failed |
644
|
You will not receive network access pop-ups |
645
|
Internal authentication error |
646
|
The account is not permitted to log on at this time of day |
647
|
The account is disabled |
648
|
The password has expired |
649
|
The account dies not have Remote Access permission |
650
|
The Remote Access server is not responding |
651
|
Your modem (or other connecting device) has reported an error |
652
|
Unrecognized response from the device |
653
|
A macro required by the device was not found in the device INF file section |
654
|
A command or response in the device INF file section refers to an undefined macro |
655
|
The macro was not found in the device INF file section |
656
|
The macro in the device INF file contains an undefined macro |
657
|
The device INF file could not be opened |
658
|
The device name in the device INF or media INI file is too long |
659
|
The media INI file refers to an unknown device name |
660
|
The device INF file contains no response for the command |
661
|
The device INF file is missing a command |
662
|
Attempted to set a macro not listed in the device INF file |
663
|
The media INI file refers to an unknown device type |
664
|
Cannot allocate memory |
665
|
The port is not configured for Dial-Up Networking/Remote Access |
666
|
Your modem (or other connecting device) is not functioning |
667
|
Cannot read the media INI file |
668
|
The connection dropped |
669
|
The usage parameter in the media INI file is invalid |
670
|
Cannot read the section name from the media INI file |
671
|
Cannot read the device type from the media INI file |
672
|
Cannot read the device name from the media INI file |
673
|
Cannot read the usage from the media INI file |
674
|
Cannot read the maximum connection BPS rate from the media INI file |
675
|
Cannot read the maximum carrier BPS rate from the media INI file |
676
|
The line is busy |
677
|
A person answered instead of a modem |
678
|
There is no answer |
679
|
Cannot detect a carrier |
680
|
There is no dial-tone |
681
|
General error reported by device |
682
|
ERROR WRITING SECTIONNAME |
683
|
ERROR WRITING DEVICETYPE |
684
|
ERROR WRITING DEVICENAME |
685
|
ERROR WRITING MAXCONNECTBPS |
686
|
ERROR WRITING MAXCARRIERBPS |
687
|
ERROR WRITING USAGE |
688
|
ERROR WRITING DEFAULTOFF |
689
|
ERROR READING DEFAULTOFF |
690
|
ERROR EMPTY INI FILE |
691
|
Access denied because username and/or password is invalid on the domain. (check your password) |
692
|
Hardware failure in port or attached device |
693
|
ERROR NOT BINARY MACRO |
694
|
ERROR DCB NOT FOUND |
695
|
ERROR STATE MACHINES NOT STARTED |
696
|
ERROR STATE MACHINES ALREADY STARTED |
697
|
ERROR PARTIAL RESPONSE LOOPING |
698
|
A response keyname in the device .INF file is not in the expected format |
699
|
The device response caused buffer overflow |
700
|
The expanded command in the device .INF file is too long |
701
|
The device moved to a BPS rate not supported by the COM driver |
702
|
Device response received when none expected |
703
|
ERROR INTERACTIVE MODE |
704
|
ERROR BAD CALLBACK NUMBER |
705
|
ERROR INVALID AUTH STATE |
706
|
ERROR WRITING INITBPS |
707
|
X.25 diagnostic indication |
708
|
The account has expired |
709
|
Error changing password on domain |
710
|
Serial overrun errors were detected while communicating with your modem. (Com Over run) |
711
|
RasMan initialization failure. Check the event log. |
712
|
Biplex port is initializing. Wait a few seconds and redial. |
713
|
No active ISDN lines are available |
714
|
Not enough ISDN channels are available to make the call |
715
|
Too many errors occurred because of poor phone line quality |
716
|
The Remote Access IP configuration is unusable |
717
|
No IP addresses are available in the static pool of Remote Access IP addresses. |
718
|
PPP timeout |
719
|
PPP terminated by remote machine |
720
|
No PPP control protocols configured |
721
|
Remote PPP peer is not responding |
722
|
The PPP packet is invalid |
723
|
The phone number, including prefix and suffix, is too long |
724
|
The IPX protocol cannot dial-out on the port because the computer is an IPX router |
725
|
The IPX protocol cannot dial-in on the port because the IPX router is not installed |
726
|
The IPX protocol cannot be used for dial-out on more than one port at a time |
727
|
Cannot access TCPCFG.DLL |
728
|
Cannot find an IP adapter bound to Remote Access |
729
|
SLIP cannot be used unless the IP protocol is installed |
730
|
Computer registration is not complete |
731
|
The protocol is not configured |
732
|
The PPP negotiation is not converging |
733
|
The PPP control protocol for this network protocol is not available on the server |
734
|
The PPP link control protocol terminated |
735
|
The requested address was rejected by the server |
736
|
The remote computer terminated the control protocol |
737
|
Loopback detected |
738
|
The server did not assign an address |
739
|
The remote server cannot use the Windows NT encrypted password |
740
|
The TAPI devices configured for Remote Access failed to initialize or were not installed correctly |
741
|
The local computer does not support encryption |
742
|
The remote server does not support encryption |
743
|
The remote server requites encryption |
744
|
Cannot use the IPX net number assigned by the remote server. Check the event log. |
752
|
A syntax error was encountered while processing a script |
|
|
Back to Top
|
|
|